Sapido RB-1800 Bedienungsanleitung PDF herunterladen (Seite 6)





This is a slightly more complicated wireless connection method, but

it provides additional beneﬁts. Your computer communicates with a

central access point. The 34972A also communicates with the same

central access point through the mobile router. This method requires the

availability of an additional WLAN (a central access point on a wireless

network), but as a result, you will be able to access other Web sites and

instruments with your computer if the WLAN provides those capabili-

ties. Other computers will be able to communicate wirelessly with the

34972A simultaneously with your computer.

The following part 1 procedure is based on the Sapido mobile router

Wi-Fi AP mode starting from the factory default settings. You can

restore all of the factory default settings in one of two ways: with the

mobile router powered, either press and hold (for 10 seconds, then

release) the recessed RESET button (not the WPS button) on the front

of the mobile router, or, if you can access the mobile router’s built-in

Web server, click System Management > Proﬁles Save, then

Reset. Following a reset, wait for about 90 seconds for the mobile

router to reboot.





You need to perform the steps in part 1 only once to conﬁgure the

mobile router’s Wi-Fi AP mode. The conﬁguration is saved even

with power removed. Afterwards, you will be able to use your 34972A

wirelessly by following the steps in part 2.

1. Set the Sapido mobile router mode switch

–With power to the mobile router removed, set the mode switch

on the back of the router to W (Wi-Fi AP mode).

2. Wire mobile router connections

–To the LAN port, connect an Ethernet

(RJ-45) cable.

–Connect the other end of the Ethernet

cable to the computer’s LAN port.

–Connect power to the mobile router

to turn it on (see measurement tip on

page 2 on powering your mobile router).

3. Conﬁgure mobile router

–Before you proceed, make sure the

mobile router has been powered up

in Wi-Fi AP mode, as described in the

previous two steps.

–Temporarily disable your computer’s

wireless connection to avoid conﬂicts

between the computer’s wireless and

wired-LAN connections. Wait for the

mobile router to assign an IP address

to your computer.

–Open a Web browser. Connect to the mobile router’s built-in

Web server by entering “192.168.1.254” as the URL. The Sapido

mobile router’s login screen should appear.

–Log in using “admin” as both the user name and password. These

are the default settings; once you are logged in, you can change

them if necessary. The Network Conﬁg screen should appear.

–If the wireless network to which you want to connect has security,

conﬁgure the mobile router with the security settings. Click

Wireless, then Security on the left side of the screen and

provide the required information. Do not be concerned about the

Select SSID ﬁeld for now; leave it set to the default setting. Be

sure to click Apply Change and wait for the router to reconﬁgure

itself (about 25 seconds).

–Click Wireless > Site Survey. A list of available wireless

networks should appear, as shown in Figure 5. If needed, you

can refresh the list by clicking Refresh. Find the one to which you

would like to connect the 34972A and select the radio button next

to it. Click Connect. You should see a screen showing “Connect

successfully!”. Click OK. The wireless network you chose along

with its security conﬁguration, if any, will be saved in the mobile

router for Wi-Fi AP mode even if you remove power from it.

–At this point, if desired (not necessary), you can use the mobile

router as a wireless adapter for your computer if you disconnect

(for at least 30 seconds) and reconnect the LAN cable. The mobile

router will assign a new IP address to your computer. After your

computer is assigned a new IP address by the router, you should

be able to connect to the internet (if available from the wireless

network to which you are connected) with the computer. The

wireless connection path is from your computer, through the

Ethernet cable to your mobile router, to your wireless network

without turning on any built-in wireless adapters in your computer.

If you want to, you can conﬁrm the mobile router is connected and

working properly by accessing a Web site. Now that the mobile

router is conﬁgured properly, it can be used to provide wireless

connectivity for the 34972A.

–Disconnect the Ethernet cable from the computer.

(In part 2, step 3, you will connect it to the 34972A.)

Figure 5: In Wi-Fi AP mode, the Sapido mobile router shows a list of available wireless networks. Select

the one to which you want to connect your 34972A by clicking the radio button next to it.

1 2 3 4 5 6 7 8 9

Kommentare zu diesen Handbüchern

Keine Kommentare

Sapido RB-1800 Bedienungsanleitung Seite 6

Kommentare zu diesen Handbüchern